CP2E – read user manual online or download in PDF format. Pages in total: from the Crestron website (). 2. CP2E only. 2- Series Engine. At the heart of the CP2 & CP2E is the powerful bit Freescale. Crestron CP2E Pdf User Manuals. View online or download Crestron CP2E Operation Manual.
|Published (Last):||5 December 2016|
|PDF File Size:||18.97 Mb|
|ePub File Size:||12.36 Mb|
|Price:||Free* [*Free Regsitration Required]|
The Software is licensed and not sold. Tighten the terminal block screws to lock the wire and bussing strip into place. Therefore, if you use a PWRU power supply rated at 50 wattsyou will have 26 watts of power left over to run additional Cresnet devices. If less than four, the strip can be trimmed to size with a pair of scissors or wire snips.
Increase the separation between the equipment and receiver. Refer to the diagram following step 3 for a detailed view.
Each network device must have a unique Net ID. Pressing it alone while the system is running restarts the creztron. Particular attention should be given to supply connections other than direct connections to the branch circuit. If the unit is a home-run from a Crestron system power supply network port, the Cresnet power usage of that unit is the Cresnet power usage of the entire run.
As long as the sum total of the devices on Cresnet does not exceed 26 watts, you will be fine. Apply the feet near the corner edges on the underside of the unit.
The pinout of each 9-pin port is non-standard; it contains RS pins in addition to RS The only tool required is a 2 Phillips screwdriver. This may result in a conflict with some equipment and therefore all nine pins should not be used. The bussing strips are constructed with four terminal block positions and may be trimmed to size for various applications or different devices.
For larger xp2e i. Operations Guide — DOC. Windows is a registered trademark of Microsoft Corporation.
These ears must be installed prior to mounting. Table of Contents Add to my manuals Add.
Crestron CP2E Manuals
Loosen the terminal block screws and insert the first leg of the bussing strip into the first common position of the terminal block. Use manuxl in wiring installations to avoid applying 24 VDC to Cresnet wiring from an AC power pack as well as from a system device that contains its own power supply.
The Software is protected by copyright laws and international treaty provisions. If further assistance is cresron, please contact a Crestron customer service representative. This Agreement may only be modified crestronn a writing signed by an authorized officer of Crestron. In the event that the clock fails, only an authorized technician should replace it. Strip and Tin Wire When daisy-chaining Cresnet units, strip the ends of the wires carefully to avoid nicking the conductors. The port is modem compatible modem and PC cables not included.
SystemBuilder from the Crestron website and examine the extensive help file. To prevent the possibility of electrical shorts, it is essential that these conductors do not touch any uninsulated portion of the bussing strip. When calculating the length of wire for a particular Cresnet run, the wire gauge and the Cresnet power usage of each network unit to be connected must be taken into consideration.
Confirm properly defined signal definition in the program. Any implied warranties that may be imposed by law are limited to the terms of this limited warranty. Display the network device tree Tools Network Device Tree to show all network devices connected to the control system. Twist together the ends of the wires that share a pin on the network connector, and tin the twisted connection.
CRESTRON CP2E 说明书_百度文库
In the event repairs are found to be non-warranty, return freight costs shall be paid by the purchaser. To utilize the bussing strip, determine the number of relays to be commoned for the equipment being installed.
If Cresnet HP is used for the same run, its length could extend to feet.
Without prejudice to any other rights, Crestron may terminate this Agreement immediately upon notice if you fail to comply with amnual terms and conditions of this Agreement.
Verify that serial cable is wired correctly for RS, or Enter text from picture: Purchasers should inquire of the dealer regarding the nature and extent of the dealer’s warranty, if any. To avoid damage to the CP2 or CP2E unit, be sure the mating Cresnet cable connector is properly aligned before attempting to insert it.
First-time users will cp2d to establish a user account to fully benefit from all available features. Don’t show me this crestfon again. You can also log onto the online help section of the Crestron website to ask questions about Crestron products.
Crestron CP2 Operation Manual
This Agreement may only be modified by a writing signed by an authorized officer of Crestron. This warranty statement supersedes all previous warranties. This document was prepared and written by the Technical Documentation department at: This device complies with part 15 of the FCC rules. The CP2 and CP2E are compact control systems designed for small to c2e sized residential and commercial control applications.
Hardware or software failure, hardware incompatibility with software definitions or programming error. Danger of explosion if battery is incorrectly replaced. When setting the IP ID, consider the following: Cresnet power usage of the entire chain.
This manuwl generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.