ASTM D3183 PDF

This standard is issued under the fixed designation D ; the number 1 This practice is under the jurisdiction of ASTM Committee D11 on. Buy ASTM D Standard Practice for Rubber—Preparation of Pieces for Test Purposes from Products from SAI Global. Buy ASTM D PRACTICE FOR RUBBER – PREPARATION OF PIECES FOR TEST PURPOSES FROM PRODUCTS from SAI.

Author: Zulugis Kerisar
Country: Bermuda
Language: English (Spanish)
Genre: Sex
Published (Last): 19 January 2004
Pages: 247
PDF File Size: 6.79 Mb
ePub File Size: 14.81 Mb
ISBN: 881-4-50617-975-7
Downloads: 58023
Price: Free* [*Free Regsitration Required]
Uploader: Nirr

This standard is subject to revision at any time by the responsible technical committee and must be reviewed every?

Such pieces are used as a source from which specimens are obtained for testing. The buffing may be either against the drum, against one of the pulleys, or against the taut band between the pulleys. Attachments are available for splitting and cutting sections from cable sheathing and hose. asm

ASTM D3183 – 10(2015)

The sheets shall be vulcanized in accordance with Practice D and shall have an equivalent state of vulcanization judged from such properties as can be determined on the product.

NOTE 1—For production quality control, testing within 1 to 6 h after vulcanization may be necessary to monitor plant operation.

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. The pieces shall be prepared in accordance with Section 7. The abrasive bands should be of textile or paper, or a combination of the two, with the abradant based on aluminum oxide or silicon carbide bonded to its surface with a resin unaffected by water.

If a liquid is used, place the rubber so as to permit free evaporation of the liquid. The successive cuts should be progressively thinner to avoid over-heating. The American Society for Testing and Materials takes no position respecting wstm validity of any patent rights asserted in connection with any item mentioned in this standard.

  DESCARGAR GRATIS TEORIA SOCIOLOGICA CLASICA GEORGE RITZER PDF

Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. For removal of greater thicknesses of rubber, use the cutting techniques indicated in 7.

NOTE 2—Wheels of to mm 5 to 6-in. NOTE 3—Grit sizes of 0. Procedures are given for preparing pieces suitable for preparing specimens of the product. The machine consists of a motor- or hand-driven disk cutter of suitable diameter with a movable cutting table that transports the sample to the cutting edge.

The knife should be lubricated with a mild soap solution to ease the cutting operation. Users of this standard are expressly advised that determination of the validity of aetm such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. The sheets shall have one of the following thicknesses unless another thickness is technically necessary: Allow time for the complete evaporation of the liquid before the specimens are cut and tested.

ASTM D e1. Equipment should be e3183 for slow feeding of the material to the abrasive band and for securing the material without excessive deformation Note 3. A superscript epsilon e indicates an editorial change since the last revision or reapproval.

Do not carry out buffing beyond the point where unevenness of thickness has been eliminated. Clamping devices should be available to secure the rubber. An adjustable slow-feed mechanism is?

ASTM D – 02 Standard Practice for Rubber—Preparation of Pieces for Test Purposes from Products

It is important that the wheel should run true, without vibration, and that the abrasive surface based on aluminum oxide or silicon carbide is true and sharp. Current edition approved March 30, Preparation of Pieces 7.

  KURBAN SAIF ALI AND NINO PDF

A number in parentheses indicates the year of last reapproval. Adjustments should be available to vary the thickness of cut, and feed rollers should be provided to transport the material past the knife.

Take care to avoid excessive stretching of the rubber during the separation, by separating a little at a time while the rubber is gripped near the point of separation. Uneveness of surface may result from contact with fabric components, cutting techniques, or other reasons.

In operation, cuts removing several tenths of a millimetre of rubber are practicable as the heat build up is much lower than with the method of 7. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM Headquarters. Last previous edition D — Originally published as D — Some skiving machines can separate plies of rubber as in belts, hose, and tires see 7.

Provision should be made for continuous sharpening of the cutting edge. This standard has been approved for use by agencies of the Department of Defense. Suitable means should be provided for securing the rubber to prevent excessive deformation and for controlled traversing of the rubber pass the abrasive wheel Note 2. Procedures in this section describe the preparation of pieces from vulcanizates that are too thick, have uneven surfaces, or contain textiles.

VPN