ANILAM 1100M PDF

I have an anilam that quit working. Will the drive motors from the anilam work with a mach 3 system. And where does a person find a. Hello, Out Anilam m 2 axis system is giving us no video and the computer will not boot. Does anyone know how to repair the system?. Anilam is the company that makes the control. I run a Sharp knee mill with a Aniliam M control. I’m not familiar with the M or sure what.

Author: Bazilkree Maukinos
Country: Cape Verde
Language: English (Spanish)
Genre: Software
Published (Last): 28 January 2007
Pages: 148
PDF File Size: 11.88 Mb
ePub File Size: 4.19 Mb
ISBN: 430-5-83239-353-9
Downloads: 63836
Price: Free* [*Free Regsitration Required]
Uploader: Voodooktilar

The following drawing is the PC mechanical drawing Part s: To recap, when I started it, the display said ‘cmos battery indication low’, plus the keyboard wouldn’t work.

Everything said above and If you turn on backlash compensation you must change the Servo Up Delay parameter, this parameter is located in the Miscellaneous section and Must be set to 3! If there is a printer connected it MUST be turned ailam. Highlight Machine Installation and press the Enter key.

Once you know which cable s that is causing the problem, check to see what the other end 1100m connected to and unplug the cable if possible. If you are in manual mode the servo most definitely will not energize. This message means the control sent a signal out of the motion board but did not see any counts coming back in.

It gets easier as you go Does the motor for the axis that is shutting down have torque? Does anyone know how to repair the system? PH Fax E-mail jbouvier anilam. Turn off the VAC power.

  ESFEROCITOSE HEREDITRIA PDF

Anilam M Programming Manual CNC Three Axis pdf – CNC Manual

Software Hi Ben, Here is the contact you need. Turn off the VAC power and open the computer cabinet. If you want you could reinsert the disk which had the backup of your programs. You really do have backlash in the system and need to fix the mechanical problem.

Wipe this glass on both sides from one end to the other. Change to Adjust Endpoint. To enable the message do the following. Do not Attempt to run your anila at this point! If yes check inside the computer for a loose connection on the motion board. If the encoder is 1100j of the motor and is not easily swapped to another axis, then swap motors to see if the problem will move with the motor into anilak working axis.

If you have voltage on one side but not the other you have a blown fuse. If the voltage is still there the short is caused by something wired to the P4 cable. Upgrade Hi, I have not heard for anyone doing this. If swapping the anilaam the problem moved to the other axis, then the problem is in the encoder which is built into the motor.

The following message is what you should see. If the voltage is now present then you have a short on the 24 volt positive output to ground.

Anilam 1100M Programming Manual CNC Three Axis

No torque on the specified axis. This drive card is not an Anilam part. You should get continuity across these pins if anilan switch is good and the wiring is good.

Signal gain not set properly. If yes, do you have scales or encoders on this axis? I have the disk but it is corrupted. All axis should have the same characteristics in the motor and motor cable wiring.

  DEEPAK CHOPRA KNJIGE PDF

I wish I had a video to fall back on when I was starting cnc, would have made my life easier. If all of the lights are out this means your limit switch string is open.

Press the F2 key to run the X axis in the positive direction. Their customers typically are more worried about just getting the thing running than the cost of getting it running. I am wondering if you know what the approx price to have the system overhualed is? The mill I run is good for one-off stuff. We work anliam a lot. If you have less then 5. Do you have 24VDC from the 24 volt power supply?

Controller & Computer Solutions > Anilam m software

The original 3 axis board has 1 DB25 and 1 DB9 11000m on it. If L4 LED is on the control is in manual mode.

Contact Anilam or your local Distributor to get the defective part replaced. This is going to erase memory and clear your problem. Posted via Mobile Device. Does the K4 relay on the PC board energize? You should see VAC across these two points. Does the axis that is shutting down work in feed but just not in rapid? Use the down arrow key Highlight Printer and press the Enter key.

Of course make sure the power is off before you remove the motion board. Press the Enter key.

VPN