EDSVSS−9. 9ä. System Manual. (Extension). 75 kW l. EVSxS EVSxS. Servo inverter. Global Drive. The System Manual is the basis for the description of the vector frequency inverter. Together with the System Manual (extension), document number. The vector range of frequency inverters is also perfectly equipped to handle complex applications, such as deployments in dosing, filling and feedforward.
|Published (Last):||13 November 2016|
|PDF File Size:||17.37 Mb|
|ePub File Size:||4.60 Mb|
|Price:||Free* [*Free Regsitration Required]|
Positive limit switch was reached. Sensor for detecting the internal temperature indicates undefined values.
Error of the program function “set position value”. The angle difference between 930 and actual position is larger than the following error limit set under C Positive position limit C elnze exceeded. Have a look at this document from Helmholtz, it gives an example on whatmust be set and how to so the CAN modules can read and write to a drive:.
New question published by Shahjee is split to a separate thread with the subject brake functions or Brakes will Automatically applied. Site Explorer Site Explorer. Control drive in negative direction. Increase following error limit under C During initialisation of the controller, an incorrect power stage was detected.
servo PLC – Lenze in Germany. As easy as that.
Error “positive position limit”. Complain wrong Brand wrong Model non readable.
Control drive in positive direction. Change the parameter set from absolute to relative. Internal fault power stage.
Error “negative limit switch”. You could probably recreate the Helmhotz drivers by yourself, if you knew how the CAN module communicates with the CPU over the backplane, how the CAN module must be parametrized for CAN BUS and how toexchange betweenthe CAN module and the drive,, If you do not have the information, 9300 strongly suggest you get purchase the Helmholts CAN 93000 software and the handling blocks for the S, so you can concentrate on your project making the drives do what you need them to do instead of finding ways to talk to the drives.
Error in positioning program. Follow us on Twitter Youtube. Hello aran; Anything is possible, with enough ressourcesinformation and time.
9300 vector frequency inverters
Anything is possible, with enough ressourcesinformation and time. Drive cannot follow the digital frequency I max limit. Troubleshooting and fault elimination. Impermissible programming Check position program: Handling blocks should be ordered from Helmholtz, look on page 96 of the document page 8 of If necessary, adapt the position limit values or check whether the program function “set position value” is to be applied.
Sensor for detecting the heatsink temperature indicates undefined values.
If you do not have the information, I 9030 suggest you get purchase the Helmholts CAN parametrization software and the handling blocks for the S, so you can concentrate on your project making the drives do what you need them to do instead of finding ways to talk to the drives.
Start homing in the program.
Best regards CS Moderator. Temperature inside the controller Sensor for detecting the internal temperature indicates undefined values.
Heatsink temperature sensor error. Perform one of the following functions and restart:. In the case of absolute positioning, no homing was performed before the lwnze positioning.
9300 series servo inverters
Error “actual reference dimension offset”. Hope this helps, Daniel Chartier. Perform one lene the following functions and restart: An absolute parameter set C was performed during relative positioning position mode C Troubleshooting and fault elimination, System error messages general error messages — Lenze 0. Actual reference dimension offset C outside the position limits.
Error “positive limit switch”. A parameter set with final speed lenzd be followed by a parameter set with positioning; it is not permissible to wait for input. Have lnze look at this document from Helmholtz, it gives an example on whatmust be set and how to so the CAN modules can read and write to a drive: Find out why the value was not reached e.
Negative limit switch was reached.
Error “negative lejze limit”. Product Support Services Forum mySupport. Negative position limit C was not reached. Parameter set mode is absolute instead of relative. The reference point is not known. Drive cannot follow the digital frequency I. Temperature inside the controller.
Find out why the value was exceeded e.