ELIWELL ID970 PDF

Buy Eliwell On/Off Temperature Controller, 74 x 32mm, NTC, PTC Input, 12 V ac/ dc Supply ID Browse our latest on-off-temperature-controllers offers. Buy Eliwell On/Off Temperature Controller, 74 x 32mm, PTC Input, V ac Supply, → +°C Measurement Range ID V 8A+PTC. Browse our. In order to configure the instrument for this purpose you must access the folder identified by the “Add” label and use the parameters “dEA” and “FAA”. ID LX.

Author: Keshakar Mara
Country: Ethiopia
Language: English (Spanish)
Genre: History
Published (Last): 21 October 2005
Pages: 358
PDF File Size: 4.76 Mb
ePub File Size: 16.64 Mb
ISBN: 375-7-56088-125-3
Downloads: 53165
Price: Free* [*Free Regsitration Required]
Uploader: Tygokora

The parameter indicates that a elieell is active on the relay actuations of the generic compressor. In normal conditions, the labels for the Set point value is found in the menu.

The indicated time must elapse between two subsequent switch-ons of the compressor. Always switch off machine before working on electrical connections. If you do not enable JavaScript, certain features in this page will not function correctly.

Single stage controller for temperature ID View with decimal point. Temperature value understood as distance from the Setpoint or as an absolute value based on Att which if exceeded in an upward direction triggers the activation of the alarm signal.

In addition, the 16 A compressor relay options and the buzzer are provided. There are 2 operating modes determined by parameter AtP: The programming parameters are downloaded when the device is switched on.

  ARIHANT DC PANDEY ELECTRICITY AND MAGNETISM SOLUTIONS PDF

At least the indicated time id790 elapse between switch-off of the compressor relay and the successive switch-on. Make sure that the power voltage complies with the device voltage.

Single stage controller for temperature. The two sets are interdependent: Eliwe,l LX Single stage controller for temperature.

Eliwell ID MC (Milk) |

Minimum possible setpoint value. Temperature alarm signal delay time. The Setpoint value appears on the display. Drill a 29×71 mm hole, insert ir970 tool and fix it in place with the brackets provided. Set point setting folder; -Pb1: The instrument has screw terminals for connecting electrical cables with a maximum diameter of 2.

It is still eliwell to enter parameter programming and modify the parameters, including the status of this parameter, in order to allow keyboard unlocking. For this page to function properly, you must enable JavaScript. The sensor has no connection polarity and can be extended using an ordinary bipolar cable note that extending the probe may affect the electromagnetic compatibility EMC of the instrument: It is classified as follows: ID Single stage controller for temperature.

Description Technical Schema Description: Compressor off time in the event of a faulty probe. It’s a community-based project which helps to repair anything. Users must not be able to access parts with dangerous voltage levels under normal operating conditions. Eliiwell from reset Connect the copy card when eliweol instrument is OFF.

JavaScript is disabled in your browser. Eliwell reserves the right to make any changes or improvements without prior notice and at any time.

  BROTHER FAX 8070P PDF

Delay after switching off. Any protection devices required to comply with product requirements or dictated by common sense due to obvious safety reasons should be installed externally. HSE maximum set cannot be less than LSE minimum set and vice versa Di970 activation time in the event of a faulty probe. The relay contacts are voltage-free.

Delay time in activating the outputs after switch-on of the instrument or after a power failure. The password is enabled if the value of the PA1 parameter is not 0. TTL for connection to Copy Card 3 outputs on relays: Probe cables, power supply cables and the TTL serial cable should be kept separate from power cables.

When enabled value other than 0it constitutes the access key for level 1 parameters. Programming parameter transfer from Copy Card to instrument.

Eliwell ID970 MC (Milk)

They are provided with a PTC thermostatic probe input NTC can ld970 selected by parameter and two relay outputs for compressor and defrost management. Every time the compressor stops, a defrosting cycle is performed according to parameter dty dOH Defrost start delay time from start up of instrument. The parameter indicates that the protection is active on compressor relay actuations.

VPN